Produkty dla cynelog 35 analogi (7)

Format 96 x 96 mm Two/three step, continuous controller Sensor monitoring Up to 5 outputs 1 Analogue input (universal) 1 Binary input 1 Relay output (closing contact) Self-optimization (autotuning) for exact PID control Manual/automatic mode Configurable limit monitoring (alarms) Setpoint switching Level/keyboard locking RS485 interface (Modbus RTU) Ramp and timer function Firing curve for ceramic furnaces Plug-in controller module Setup interface (USB Mini-B)

The LPX low-pressure calibrator is a high-precision calibration instrument for pressures between -0,85 bar and 10 bar (after taring to ambient pressure). The functional calibrator is supplied in a sturdy carrying case and pressure can be quickly generated manually. It is therefore ideal for use in the field. The pressure is measured by the integrated LEX1 manometer and output both on the display and via the RS485 interface. Additional functions such as zero point resetting, peak and trough pressure value indication and leak measurement make it even easier to take measurements. Pressure Ranges:-0,85…10 bar Accuracy:0,05 %FS Interfaces:RS485 Display:5-digit LCD display Special characteristics:For air pressure

Sustainable solution for process measurement, control and data log Compatible to the wide range of INFICON active gauges, the new VGC50x series of active gauge controllers are able to monitor and data log the entire pressure range from 10⁻¹⁰ to 1500 mbar (10⁻¹⁰ to 1125 Torr) and the set point status. 1×10 -3×F.S. …1×F.S. 1×10 -3×F.S. …1×F.S. 1×10 -3×F.S. …1×F.S. 5×10 -4…1500 5×10 -4…1500 5×10 -4…1500 5×10 -10…1500 5×10 -10…1500 5×10 -10…1500 mbar, Torr, Pa, hPa, Micron, V mbar, Torr, Pa, hPa, Micron, V mbar, Torr, Pa, hPa, Micron, V Display:LCD, LED backlight Rate:10 CDG (A/D):1×10 -3×F.S. …1×F.S. PCG:5×10 -4…1500 PSG:5×10 -4…1000 MPG:1×10 -9…1000 PEG:1×10 -9…1×10 -2 MAG:1×10 -9…1×10 -2 BCG:5×10 -10…1500 BPG:5×10 -10…1000 HPG:2×10 -6…1000 Measurement unit (selectable):mbar, Torr, Pa, hPa, Micron, V Adjustment range:sensor dependent Hysteresis:adjustable Relay contact:floating changeover contact Contact rating:30 / 1 Connector:D-sub, 15-pin, male Range:0 ... 10.3, sensor analog output signal Connector:D-Sub, 15-pin, male Connector:USB slave, master and Ethernet, USB Typ A (stick), USB Type B, FCC68/RJ45 Supply:100 ... 240 Frequency:50 ... 60 Consumption:≤45 Operation temperature (ambiance):+5 ... +50

Mikro-Sensor zur präzise und zuverlässige Messungen von H2S und CH4S. Messbare Parameter:H2S / CH4S Messbereich (ppm):0 – 1 | 0 – 20 | 0 – 200 Zertifizierte Nachweisgrenze (ppm):0.01 | 0.03 | 0.2 Auflösung (ppm):0.001 Temperaturbereich (°C):-20 bis +40

Incremental, length and angle measurement Profile MA55: LED display (1 line of 5 digits) Input for incremental encoder recognition of the counting direction for length and angle measurement Free programming via front keyboard Non-volatile parameter storage (EEPROM) With reference connection Integrated quadruple evaluation of counting pulses Compact design

Display accuracy max. 1 μm. Repeat accuracy max. ±1 μm. High-contrast LCD, 12-digit LCD dot matrix. Incremental measurement and reset function. Direct reference/offset value input. Reference input. Works with sensor MS100/1. Option: serial interface RS232/RS485/switching output. Option: TG01 bench housing.

Freely programmable, compact measurement display. Optionally, the positions of incremental measurement systems or rotary speeds as well as number of pieces can be displayed combined with commercially available initiators or light barriers. Incremental, length, angle, rotational speed or number of pieces measurement. LED display (1 line of 5 digits). Inputs for incremental sensors, length and angle measurement, rotational speed or number of pieces. Free programming via front keyboard. Incremental measurement function (operating mode I), actual value memory (operating modes I and S). With reference connection. Programming enabled via external input (keyswitch). Compact design.